This Oakville project was a full-house finish carpentry package completed by Wood Job Finish Carpentry, led by Jack Cenk Ozer. The work included tall interior doors, custom jamb work, casing, window extensions, barn door hardware and a fire-rated garage entry door.

The main doors were 96-inch solid-core one-panel shaker doors. They were heavy, tall and not forgiving. With this type of door, the opening, jamb, hinge placement, reveal, latch alignment and casing all have to be handled carefully. A small mistake that might disappear on a light hollow-core door becomes much easier to notice on a tall solid-core door.

For Jack, this kind of project is exactly where owner-led finish carpentry matters. Many of the decisions were made on site: how the jambs should sit, how the casing should meet the wall, how the deep window extensions should be prepared, and how the tall doors should feel once installed.

What the Oakville Home Needed

The house needed more than standard door hanging. The project involved a full package of finish carpentry details across the home.

The work included:

• 96-inch solid-core one-panel shaker interior doors
• Door jamb preparation and installation
• Interior door casing
• Tall window jamb extensions
• Window casing and trim
• Barn door installation with black sliding hardware
• Fire-rated garage entry door installation
• Trim work around high ceilings and crown moulding areas
• Full-house finish carpentry coordination before final paint and touch-ups

This was the kind of project where the separate details had to feel connected. The doors, window extensions, casing, crown lines and base conditions all had to work together.

96-Inch Solid-Core Shaker Doors

The interior doors in this Oakville home were tall 96-inch solid-core one-panel shaker doors.

These doors give a room a cleaner and more substantial feel, but they also ask more from the installer. They are heavier than typical hollow-core doors. They put more pressure on the hinges. They show poor alignment quickly. If the jamb is not set properly, the door can reveal the problem every time it swings or latches.

For this project, the doors were prepared and staged before installation. The jambs and casing had to be planned carefully so the doors could sit properly in the openings and still leave clean, consistent reveals.

A tall door should not feel like it is fighting the frame. It should swing, close and sit in the opening with control.

Preparing Jambs and Casing Before Installation

Several parts of the work were prepared before being installed into the openings. This included door jamb assemblies and window extension pieces.

That preparation matters. In finish carpentry, the cut is only one part of the job. The way the jamb is assembled, the way the casing meets the wall, and the way the reveal is planned all affect the final result.

On a full-house project, consistency also matters. One door should not feel completely different from the next. Casing width, reveal, hinge side, hardware height and trim lines all need to feel intentional as you move through the home.

Tall Window Extensions and Scaffold Work

One of the more demanding parts of this Oakville project was the tall window work.

Some of the window openings were very high, with deep returns and high ceilings. Scaffold was needed to reach the upper sections safely and to install the trim and extensions properly.

Tall windows make mistakes easier to see. Light runs across the surface. Long vertical lines draw the eye. If the extension or casing is not fitted cleanly, the whole opening can look unfinished.

The window extensions were prepared and then fitted into place, with attention to the depth of the opening, the drywall condition and the surrounding trim lines.

Deep Basement Window Extensions and Casing Assemblies

The basement also had several deep window openings that needed custom extension work before casing could be installed.

Deep window returns are easy to underestimate. From the room side, they may look like simple rectangular openings, but the depth, wall condition, window position and casing layout all have to be measured carefully. If the extension is not built square and consistent, the casing will only make the problem more visible.

For this Oakville project, the basement window extensions and casing pieces were prepared and assembled before being installed into the openings. Building them on the floor helped control the size, corners, reveal and overall fit before the assemblies were lifted into place.

This kind of work is not only about covering the drywall edge. A deep window extension should make the opening feel finished, clean and intentional. Once installed, the extension, casing and surrounding wall need to look like they belong to the same room, not like a repair added after the fact.

Barn Door Installation

The project also included a white barn door with black sliding hardware.

Barn doors are simple in appearance, but the wall, opening, header support, track height and door clearance all need to be considered before installation. The door has to slide properly, cover the opening as intended and sit visually in line with the surrounding trim.

In a house with tall doors and clean shaker profiles, the barn door needed to feel like part of the same finish package, not an isolated feature.

Fire-Rated Garage Entry Door

Another important detail was the garage entry door. This was a fire-rated door installation, which means the door could not be treated like a standard interior slab.

With fire-rated doors, the door, frame, hardware and installation details matter as an assembly. For homeowners, the important point is simple: this is not the kind of door where the label on the slab is the only thing that matters. The opening, jamb, hardware and closing function all need to be respected.

For this Oakville project, the garage entry opening was prepared, the fire-rated door was installed, and the casing was finished around it as part of the home’s overall trim package.

See Ontario Building Code definitions for fire-protection and fire-resistance ratings.

Working Around the Real Stage of the Renovation

The photos show the project during the installation stage. Some walls were not yet painted. Some openings were still being finished. Protective floor covering was still in place. That is normal in this phase of a renovation.

Finish carpentry often happens before final paint and after several other trades have already been through the home. That means the work has to be careful, but also practical. The carpenter has to work with real site conditions: drywall edges, floor protection, unfinished surfaces, tall openings, heavy doors and other trades still moving around the project.

The goal is to leave the doors, jambs, casing and window trim ready for the next stage so the final paint work can bring everything together.

Owner-Led Finish Carpentry by Jack Cenk Ozer

Wood Job Finish Carpentry is intentionally small and owner-led. On a project like this, that matters because the small site decisions are not separate from the final result.

Jack Cenk Ozer was directly involved in the finish carpentry work, from reading the openings and planning the jambs to fitting the doors, casing and window extensions. When a tall solid-core door needs adjustment or a deep window return needs to be built cleanly, the person making the decision should also be responsible for the finished detail.

That is the difference Wood Job tries to protect: the name, the hands and the responsibility stay connected.

Why This Project Matters for Oakville Homeowners

Oakville homes often have finish details that are meant to feel clean, calm and more custom than builder-grade work. That does not mean the language has to be fancy. It means the small details have to be handled properly.

In this project, the height of the doors, the weight of the solid-core slabs, the high window openings and the amount of casing work made the finish carpentry especially important.

A full-house trim package is not only a collection of cuts. It is a sequence of decisions: how the door sits, how the casing frames the opening, how the window extension meets the wall, how the hardware lines up, and how the details feel from room to room.

Planning a Similar Door and Trim Project in Oakville?

Wood Job Finish Carpentry works with Oakville homeowners on interior door installation, solid-core door replacement, casing, trim, baseboards, window extensions, barn doors and renovation finishing details.

Planning a similar interior door, trim or window extension project in Oakville? Send clear photos of the openings, the number of doors or windows involved, your project location, and any door or trim style you are considering. Jack can review the details and let you know whether a rough estimate is possible from photos or if a walkthrough would be the better next step.

FAQs

Do you install 96-inch interior doors in Oakville?

Yes. Wood Job Finish Carpentry installs tall interior doors, including 96-inch doors, when the openings and site conditions are suitable. Tall doors need careful jamb preparation, hinge alignment, reveal control and hardware planning because their size and weight make small mistakes easier to notice.

Are solid-core doors harder to install than hollow-core doors?

Solid-core doors are usually heavier and less forgiving than hollow-core doors. They often feel better when installed properly, but they also make poor hinge alignment, twisted jambs or uneven openings more obvious.

Can you install door jambs and casing as part of the same project?

Yes. Door installation often works best when jambs, casing and surrounding trim are handled together. That allows the reveal, casing line, hardware and wall condition to be considered as one finish carpentry detail.

Do tall window extensions need special planning?

Yes. Deep or tall window openings need careful measuring and fitting. The extension depth, drywall condition, window frame, casing layout and access all affect the final result. In some homes, scaffold may be needed to work safely around high windows.

Can you install barn doors?

Yes. Barn door installation depends on wall support, track height, opening width, floor clearance and how the door will cover the opening. The goal is to make the door function properly and still feel connected to the surrounding trim.

Do you install fire-rated doors?

Yes, when the product, opening and project conditions are appropriate. A fire-rated door should be treated as more than a regular interior door. The frame, hardware, closing function and manufacturer requirements should all be respected.

Related Services